Design of icing wind tunnel experiment system for rotating blades by using natural low temperature
-
摘要: 为开展风力机旋转叶片结冰风洞试验研究，设计了一种利用寒冷地区自然低温环境的具有可变截面试验段的结冰风洞试验系统。该系统在原有常规结冰风洞的基础上改进了试验段，设置了喷雾区与非喷雾区，风力机叶片实验台可设置在非喷雾区内，而旋转叶片在转至喷雾区时进行结冰测试。为测试该系统的各项参数以及研究系统的可行性，对该试验系统的3个主要环境变量：试验段速度分布、温度分布和液态水含量分布进行了测试和标定。在此基础上，进行了绕轴旋转圆柱和叶片段的结冰试验，对2个系统下的无因次结冰面积及结冰形状进行了对比分析。结果显示该系统各项参数稳定，利用2个系统得到的结冰形状相似度高，结冰面积一致性较好，表明该系统可用于进行旋转机械结冰风洞试验研究。Abstract: In order to carry out the study on icing wind tunnel experiment for rotating blades of wind turbine, an icing wind tunnel test system with variable cross test sections by using nature low temperature in cold region was designed. Based on the original wind tunnel in the lab, the test section was reformed by adding a non-spry section. Therefore, the test station for the rotating blade of the wind turbine can be set in the non-spry section and the icing test can be finished in the water spry section. The diameter of the wind turbine rotor is not limited by the water spry section size by using this test system. To measure the main parameters and verify the test ability of this system, three main icing parameters of the test section including wind speed, temperature and liquid water content distributions were tested and analyzed. Furthermore, icing experiments on rotating cylinder and rotating blade airfoil were carried out. The test results including the icing shape and the dimensionless icing area are discussed by comparing with the author's previous results of the original icing wind tunnel tests. According to the test results, the distributions of the main parameters of the test section are stable. The icing shape on cylinders and blade airfoils obtained by both test systems agrees in some degree and the values of the dimensionless icing areas are close. The result shows that the new icing wind tunnel system can be used for the research on icing issue for rotating machinery.
-
Key words:
- wind turbine /
- icing /
- rotating blades /
- wind tunnel experiment /
- variable cross section /
- natural low temperature
-
图 2 旋转叶片试验台与可变截面试验段结构图
Figure 2. Picture of rotating blade test stand and sketch of variable-area test section
表 1 试验参数对照表
Table 1. Test parameter comparison table
r/m n/(r·min-1) t/min 原系统 0.25 600 10 本系统 0.45 333 68.3 
下载: 导出CSV
表 2 圆柱无因次结冰面积对比表
Table 2. Cylindrical icing area comparison table
ϕ=20mm ϕ=40mm 原系统 本系统 原系统 本系统 ηS 1.52 1.71 0.65 0.74
下载: 导出CSV
表 3 运行参数对照表
Table 3. Motion parameter comparison table
1号 2号 原系统 本系统 原系统 本系统 n/(r·min-1) 200 111 400 222 t/min 10 68.5 10 68.5
下载: 导出CSV
表 4 无因次结冰面积对比表
Table 4. Icing area comparison table
1号 2号 原系统 本系统 原系统 本系统 NACA0018 0.17 0.24 0.32 0.55 S809 0.42 0.61 0.33 0.55
下载: 导出CSV
-
[1] 赵振宙, 钱思悦, 郑源, 等.考虑小攻角影响立轴风轮气动性能改善方法[J].排灌机工工程学院, 2018, 36(2):146-153. http://www.cnki.com.cn/Article/CJFDTOTAL-PGJX201802011.htmZhao Z Z, Qian S Y, Zheng Y, et al. Enhancement approaches of aerodynamic performance of lift-type vertical axis wind turbine considering small angle of attack[J]. Journal of Drainage and Irrigation Machinery Engneering, 2018, 36(2):146-153. http://www.cnki.com.cn/Article/CJFDTOTAL-PGJX201802011.htm [2] 冀文举, 汪建文, 薛朔, 等.从纵横向流场分析垂直轴风力机功率随转速的变化[J].排灌机械工程学院, 2018, 36(2):166-171. http://www.cnki.com.cn/Article/CJFDTOTAL-PGJX201802014.htmJi W J, Wang J W, Xue S, et al. Analysis of vertical axis wind turbine power changing with rotating speed from vertical and horizaontal flow fields[J]. Journal of Drainage and Irrigation Machinery Engneering, 2018, 36(2):166-171. http://www.cnki.com.cn/Article/CJFDTOTAL-PGJX201802014.htm [3] 战培国.结冰风洞研究综述[J].实验流体力学, 2007, 21(3):92-96. http://www.syltlx.com/CN/abstract/abstract9577.shtmlZhan P G. A review of icing wind tunnel[J]. Journal of Experiments in Fluid Mechanics, 2007, 21(3):92-96. http://www.syltlx.com/CN/abstract/abstract9577.shtml [4] 东乔天, 金哲岩, 杨志刚.风力机结冰问题研究综述[J].机械设计与制造, 2014, (10):269-272. doi: 10.3969/j.issn.1001-3997.2014.10.081Dong Q T, Jin Z Y, Yang Z G. A review of icing effect on horizontal axis wind turbine[J]. Machinery Design & Manufacture, 2014, (10):269-272 doi: 10.3969/j.issn.1001-3997.2014.10.081 [5] 王宗衍.美国冰风洞概况[J].航空科学技术, 1997, (03):45-47. http://www.cqvip.com/QK/97819X/199703/2469416.htmlWang Z Y. Ice aerodynamic tunnel in USA[J]. Aeronautical Science & Technology, 1997, (03):45-47. http://www.cqvip.com/QK/97819X/199703/2469416.html [6] Olsen W. Survey of aircraft icing simulation test facilities in North America[R]. NASA-TM-81707 19810010552, 1981. [7] 战培国.国外结冰试验研究平台综述[J].飞航导弹, 2016, (11):70-73. http://d.old.wanfangdata.com.cn/Periodical/fhdd201611016Zhan P G. Summary of foreign icing test research platform[J]. Aerodynamic Missile Journal, 2016, (11):70-73. http://d.old.wanfangdata.com.cn/Periodical/fhdd201611016 [8] Kraj A G, Bibeau E L. Phases of icing on wind turbine blades characterized by ice accumulation[J]. Renewable Energy, 2010, 35(5):966-972. doi: 10.1016/j.renene.2009.09.013 [9] Kraj A G, Bibeau E L. Measurement method and results of ice adhesion force on the curved surface of a wind turbine blade[J]. Renewable Energy, 2010, 35(4):741-746. doi: 10.1016/j.renene.2009.08.030 [10] 孙志国. 飞机结冰数值计算与冰风洞部件设计研究[D]. 南京: 南京航空航天大学, 2012.Sun Z G. Research on numerical simulation of ice accertion and design for icing research tunnel parts[D]. Nanjing: Nanjing University of Aeronautics & Astronautics, 2012. [11] 孟繁鑫. 机翼结冰模拟中关键问题的研究[D]. 南京: 南京航空航天大学, 2013.Meng F X. Study on key problems in airfoil icing simulation[D]. Nanjing: Nanjing University of Aeronautics & Astronautics, 2013. [12] 祖孝勇, 张林, 肖斌, 等. 3m×2m结冰风洞总压探针和皮托管研制[J].实验流体力学, 2016, 30(04):76-80. http://www.syltlx.com/CN/abstract/abstract10955.shtmlZu X Y, Zhang L, Xiao B, et al. Study and development of total pressure probe and pitot tube in 3m×2m icing wind tunnel[J]. Journal of Experments in Fluid Mechanics, 2016, 30(04):76-80 http://www.syltlx.com/CN/abstract/abstract10955.shtml [13] 熊建军. 3m×2m结冰风洞摄像监视系统设计与应用[J].测控技术, 2016, 35:251-255. http://industry.wanfangdata.com.cn/dl/Detail/Periodical?id=Periodical_ltlxsyycl201603002Xiong J J. Design and application of the video system in 3m×2m icing wind tunnel[J]. Measurement & Control Technology, 2016, 35:251-255. http://industry.wanfangdata.com.cn/dl/Detail/Periodical?id=Periodical_ltlxsyycl201603002 [14] 符澄, 彭强, 张海洋, 等.结冰风洞环境对喷嘴雾化特性的影响初步研究[J].实验流体力学, 2015, 29(03):30-34. http://www.syltlx.com/CN/abstract/abstract10840.shtmlFu C, Peng Q, Zhang H Y, et al. Preliminary research on sprary nozzle atomization characteristics in icing wind tunnel environment[J]. Journal of Experiments in Fludid Mechanics, 2015, 29(03):30-34. http://www.syltlx.com/CN/abstract/abstract10840.shtml [15] 孟繁鑫, 陈维建, 梁青森, 等.引射式结冰风洞内圆柱结冰试验[J].航空动力学报, 2013, (07):1467-1474. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=hkdlxb201307004Meng F X, Chen W J, Liang Q S, et al. Experiment on cylinder icing in injection driven icing wind runnel[J]. Journal of Aerospace Power, 2013, (07):1467-1474. http://www.wanfangdata.com.cn/details/detail.do?_type=perio&id=hkdlxb201307004 [16] 易贤, 桂业伟, 杜雁霞, 等.结冰风洞水滴直径标定方法研究[J].实验流体力学, 2010, 24(5):36-41. http://www.syltlx.com/CN/abstract/abstract9882.shtmlYi X, Gui Y W, Du Y X, et al. Study on the method of droplet diameter calibration in icing wind tunnel[J]. Journal of Experiments in Fluid Mechanics, 2010, 24(5):36-41. http://www.syltlx.com/CN/abstract/abstract9882.shtml [17] 易贤, 郭龙, 符澄, 等.结冰风洞试验段水滴分布特性分析[J].实验流体力学, 2016, 30(3):2-7. http://www.syltlx.com/CN/abstract/abstract10926.shtmlYi X, Guo L, Fu C, et al. Analysis of water droplets distribution in the test section of an icing wind tunnel[J]. Journal of Experiments in Fluid Mechanics, 2016, 30(3):2-7. http://www.syltlx.com/CN/abstract/abstract10926.shtml [18] 李岩, 王绍龙, 郑玉芳, 等.利用自然低温的风力机结冰风洞实验系统设计[J].实验流体力学, 2016, 30(2):54-66. http://www.syltlx.com/CN/abstract/abstract10917.shtmlLi Y, Wang S L, Zheng Y F, et al. Design of wind tunnel experiment system for wind turbine icing by using natural low temperature[J]. Journal of Experiments in Fluid Mechanics, 2016, 30(2):54-66. http://www.syltlx.com/CN/abstract/abstract10917.shtml [19] 王绍龙, 李岩, 田川公太郎, 等.旋转叶片结冰风洞试验研究[J].工程热物理学报, 2017, 38(6):1-8. http://kns.cnki.net/KCMS/detail/detail.aspx?filename=gcrb201706015&dbname=CJFD&dbcode=CJFQWang S L, Li Y, Tagawa K, et al. A wind experimental study on icing distribution of roating blade[J]. Journal of Engineering Thermophysics, 2017, 38(6):1-8. http://kns.cnki.net/KCMS/detail/detail.aspx?filename=gcrb201706015&dbname=CJFD&dbcode=CJFQ [20] 李岩, 王绍龙, 易贤, 等.绕轴旋转圆柱结冰特性结冰风洞试验[J].航空学报, 2017, 38(2):116-126. http://industry.wanfangdata.com.cn/hk/knowledge/detail?id=kntree001001001Li Y, Wang S L, Yi X, et al. An icing wind tunnel test on icing character istics of cylinder roating arounde a shaft[J]. Acta Aeronautica et Astronautica Sinica, 2017, 38(2):116-126. http://industry.wanfangdata.com.cn/hk/knowledge/detail?id=kntree001001001 [21] 李岩, 王绍龙, 冯放, 等.绕轴旋转翼型结冰分布结冰风洞试验研究[J].哈尔滨工程大学学报, 2017, 49(4):1-8. http://kns.cnki.net/KCMS/detail/detail.aspx?filename=hebg201704009&dbname=CJFD&dbcode=CJFQLi Y, Wang S L, Feng F, et al. An icing wind tunnel experiment on the icing distribution of a blade air-foil rotating around a shaft[J]. Journal of Harbin Engineering University, 2017, 49(4):1-8. http://kns.cnki.net/KCMS/detail/detail.aspx?filename=hebg201704009&dbname=CJFD&dbcode=CJFQ -
点击查看大图
图(16) / 表(4)
计量
- 文章访问数: 269
- HTML全文浏览量: 143
- PDF下载量: 25
- 被引次数: 0
